1988-1997 Stock Ford Truck Upgrades

Harland Sharp 7.5 Pedestal Mount Roller Rockers

Harland Sharp Pedestal Mount Adjustable Roller Rockers for 460, 429, 351C, 351M/400 (1.73 Ratio)

460 EFI Guys has teamed up with Harland Sharp to offer our customers the highest quality roller rockers for their factory EFI and carbureted 460/429, 351C and 351M/400 heads.  These are a full set of adjustable full roller rockers for factory pedestal mount Ford heads.  No guide plates are required with these due to the design of the self-centering pedestal foot block. 

Why upgrade you might ask?  Don’t believe the nay-sayers.  Roller rockers make a difference.  Not all your valves are opening the same amount with stamped steel rockers.   It gets worse with higher spring pressure and higher rpm. You will get more horsepower with roller rockers with less friction and less oil temperature and breakdown.  If you’re looking for quality and performance these are the best option for consistency and accuracy in valve lift.  It will help you to pull the maximum potential out of your camshaft.

Kit includes:

  • 16 adjustable roller rockers, pedestal feet and bolts

Fits:
Pedestal mount factory Ford heads 7.5 / 460, 429, 351C, 351M/400 (1.73 ratio)
for spring pressures up to 600 lbs. at the nose of the cam.

Adjustable rocker set important notes*

  • You will need to measure and order correct length pushrods. What we have found for the length on our builds is 8.350 in. (for flat tappet) & 7.850 in. (for  Crower hydraulic roller lifters).  Typically $100 for 5/16” or $150 for 3/8” pushrods.
  • You will need to raise your 460 EFI stock valve covers ½”.  You can do this one of three ways: with a set of MediceMfg valve cover spacers, with a set of MediceMfg perimeter bolt valve cover adapters, or by adding a ½” to the height of your valve covers.

$650 (Includes S+H)

1988-97 F250/F350 460/7.5 Saginaw Power Steering Conversion Service and Kit for the EFI 460 Bracket

* If you’re doing a EFI 460 engine swap into a different year than 1988-1997 we need to know what the gearbox’s high pressure line’s threads are.*

Ditch the groaning, low pressure ford pump, and convert to our kit.  We put these brackets through a 12 step process that converts the stock bracket and allows you to use a saginaw power steering pump. These pumps are an off the shelf part from your local parts store, or you can even a chrome aftermarket pump if you want.  We also include all the needed mounting bolts, adapter fittings, a braided stainless high pressure line, the low pressure line, hose clamps. and the pulley for the conversion.  These come back to you fully cleaned, modified, with all the needed conversion parts, and fully painted.

Parts included with the conversion kit:

Modified bracket

Power steering pulley from Tuff Stuff Performance

Chrome cap / dipstick from Tuff Stuff Performance

Stainless braided high pressure line from Allstar Performance

all needed line fittings and adapters (pump and steering box)

Low pressure return line and hose clamps (dayco and gator clamps)

gold iridate grade 8 pump mounting bolts

Parts needed:

460 EFI Van saginaw pump -75$ (part # 731-2153)  Or aftermarket saginaw pump

Parts Store Rental Tools:  power steering pulley puller / press and line flaring tool (bubble flaring the end is strongly suggested)

Depending on how quickly you need your new bracket, there are two purchasing options:

Option 1: We don’t charge a core charge. You send us your old bracket, and we send you one that’s already done.

Option 2: We charge a $280 core charge. This way, if you can’t afford the down time with your truck, pre-pay the additional refundable core charge of $280. From there, we will immediately send one out. Once we receive your old bracket back in usable condition we refund the core charge.  If the water pump ear is broken off we just adjust the core charge refund down to $240

$610 (Includes S+H)
ON SALE THRU MARCH 5TH!!!
Normally $720

WITH CORE CHARGE
$890 (Includes S+H)
ON SALE THRU MARCH 5TH!!!
Normally $1000

Flowkooler - High Flow Water Pumps

Simply put, a stock volume water pump falls sadly short on a stock 460 powered truck, they simply don’t move enough volume. Even stock engines will fluctuate in temperature drastically from this problem. I have never seen anyone’s water pump keep up with these units. If you do any towing or have increased the power of your engine you will need help to move that massive amount of coolant faster. Your Ford engine and the ECU needs to stay within a specific temperature range to operate correctly. Too cold and you waste fuel, get too hot and the ECU leans the air fuel curve and overheats the engine even further. We searched high and low for a pump that actually worked with the stock radiator tubes, pump shaft, and fan bolt pattern. We were thrilled to find Flowkooler water pumps. But before we offered or recommended any part to anyone we thoroughly tested these first. We installed a few on our built up engines we were installing. What we found was this pump always held the temperature much much closer to the thermostat rating than you could ever expect out of a stock water pump.

In Stock Now!!!
1970-1987 Ford 460/429 truck car and van

(early years had a few shorter water pump bolts. This pump can be used in 88-97 by shortening those bolts and adding washers behind the serpentine brackets for spacing, but CAN NOT be used with oil/heat exchanger box). The same applies to van, car 7.5 / 460, 7.0 / 429 high flow water pump

1970-1987 Ford F-100, F-150, F-250, F-350, F-450 / Super duty with 7.5 460
1970-1987 Ford E-250 E-350 Econoline Van or Rv with 7.5 460
1970-1987 Ford 460 / 429 with 7.5 460
460 swap where you are using a stock oil filter or remote oil filter kit

$195 (Includes S+H)

In Stock Now!!!
1988-1997 Ford truck and van 7.5 / 460 high flow water pump with remote oil cooler or for swaps when using the serpentine brackets

(This has the standard large inlet and works with serpentine brackets and remote oil cooler lines. IT DOES NOT WORK WITH OIL/HEAT EXCHANGER BOX that is part of the oil filter bracket)

1988-1997 Ford F-250, F-350, F-450 / Super duty,  with 7.5 460
1988-1997 Ford E-250 E-350 Econoline Van or Rv
any year swap when using the serpentine brackets

$195 (Includes S+H)

In Stock Now!!!
1988-1997 Ford truck and van 7.5 / 460 high flow water pump w/ heat exchanger box

(the inlet on these is small to go with the oil / heat exchanger box, it does not work with the remote oil cooler trucks)

1988-1997 Ford F-250, F-350, F-450 / Super duty with 7.5 460
1988-1997 Ford E-250 E-350 Econoline Van or Rv with 7.5 460

$200 (Includes S+H)

Brian Patterson
Brian Patterson
5/5

Great way to upgrade you carb'd 460!! I bought a complete kit several years ago to upgrade the 1978 460 that I was putting in my 1965 truck. I could have gone with an aftermarket bolt-on injection unit but I love having factory stuff so I can repair the truck at local auto parts stores. I had the truck running but wanted to have the old school breather instead of the tall aluminum intake since it was going in the 65. I ordered and installed this low profile unit and love it!!!

3 years ago
Ryan Henderson
Ryan Henderson
verified ownerverified owner
5/5

This throttle body is great! So fast and responsive. I am amazed by how much power is in the old truck. I am also completely satisfied with the customer service. I was still figuring out exactly what I wanted when I called and Russel took the time to answer a lot of questions for me. I am completely happy with everything I have bought from them. I'll be calling them again when it is time to upgrade my other truck!

4 years ago
jeremiah simmons
jeremiah simmons
5/5

Did the throttle body and performance intake and it opened my truck up so much from Casper wy

4 years ago
Jeff nelson
Jeff nelson
verified ownerverified owner
5/5

Well let me start by saying my truck was completely stock 460 absolutely nothing done to it. Now I have headers redone heads just cause my old exhaust manifold studs snapped off in the head but yes headers and I had my intake done by russle and this low profile throttle body. Just like it states everything is plug and play would recommend if your not a mechanic to take pictures of where all the sensors and vacuum lines go but just so it's easier when going back together. Now that I have that put of the way the power and throttle response everything is ridiculous I still cant believe how just the three things I did literally woke this truck up I am absolutely in love with the power everything. My new 73 460 I just bought will be getting these same parts done by russle and I cant wait. The advice and help you get as well from russle is amazing he will literally help you threw the entire install and do what he can to make sure your truck is running just as good as mine is I highly recommend all of his products they are amazing.

5 years ago

1988-1997 Ford trucks with EEC-IV ECUs

Smog & Emissions Compliant Low Profile Throttle Bodies for the 7.5 liter 460

** DOES NOT WORK WITH MAF (Mass Air Flow trucks) **

SPEED DENSITY HAVE 2 INTAKE TUBES CONNECTED TO THE AIR FILTER BOX

By swapping to this throttle body, you will get better throttle response, increased horsepower, increased torque, and best of all it will improve your mpg’s. Your engine will come to life and perform like the beast it truly is. This throttle body improved our 0-60 times by 2 full seconds. We did 12 runs with the original throttle body and this one just to confirm it.  Our 1995 crew cab long bed with a 460 / C6 auto picked up 2-3 mpg’s.

Included with this kit:

  • This is our newest addition that includes extra components to retain the egr components
  • Holley low profile throttle body, throttle cable and all needed sensors
  • Throttle cable housing, inner-cable, and needed fittings for throttle and cruise control
  • Idle air bypass, pigtail and tube
  • Throttle position sensor and pigtail
  • 5/8″ tubing and elbow for driver side breather port
  • 14″ Air Filter Base (we drill and install a grommet for the IAC)
  • 1″ air filter spacer (makes the install easier with more room over the fuel rails)
  • MAP sensor and fuel pressure regulator vacuum tubing
  • 3/8″ NPT plug for the intake runner #5 (when needed)
  • ** Purchase a washable complete air Filter kit separately **

$640 (Includes S+H)

If you don’t need the additional tubing to hook up to the EGR Value – purchase this option.

$600

Chrome 14" Air Cleaner Kit with reusable filter

(Shipping is included when purchased with Throttle Body)

Flat Black 14" Air Cleaner Kit with reusable filter

(Shipping is included when purchased with Throttle Body)

14" Round Air Filter Base for Low-Profile Throttle Bodies

This is only for the Air Filter Base, not a complete Air Filter. We find these to be the perfect fit for the low-profile throttle bodies. These have a ¾ “ rise needed to clear your fuel rails. There is a metal port that connects to the driver side breather port. We also drill and install a grommet for the idle air bypass. Take the guess work and the possibility of drilling your air filter incorrectly away, we will gladly do this step. Top this off with any 14″ round air filter of your choice, and lid of your choice.

These are included with every throttle body purchase.

Fel-pro Intake Manifold Gaskets for the EFI 460 Intake

(Shipping is included when purchased with an Intake)

Ted Montanye
Ted Montanye
5/5

I am running this intake manifold on my 1995 CCLB F350 7.5l. I noticed the difference immediately. I feels that this beast can breathe so much better! I would recommend this for anyone wanting to gain some extra HP out of their old 460.

3 years ago
Ryan Henderson
Ryan Henderson
verified ownerverified owner
5/5

This intake is amazing. I inspected the intake manifold inch by inch when it arrived and I loved it. There is definitely noticeable more power now that there is better airflow. Russel does an amazing job, not only with the parts but also with his customer service. He went out of his way to make sure I got my core charged returned to me. I bought several products from these guys and I am completely satisfied with all of them.

4 years ago
jeremiah simmons
jeremiah simmons
5/5

Did the throttle body and performance intake and it opened my truck up so much from Casper wy

4 years ago
Rick Williams
Rick Williams
verified ownerverified owner
5/5

Amazing results, tons of noticeable power. The intake manifold really let the motor get air and breath.
Thanks Russell for all the awesome products, and all the continued technical support with your products. Even though it is a work in progress, it is well under way to being restored.
460 EFI guys really know how to turn the 460 into a tire ripping beast.

5 years ago
Jeff Nelson
Jeff Nelson
verified ownerverified owner
5/5

Russle did a amazing job with turn around of the intake to how it looks and performs it's seriously a huge upgrade for these old 460. I already purchased another 460 so I will be getting another one done for my other project. I have the low profile throttle body as well and I must say the throttle response and power I have now is a drastic change from how my truck was stock. I was border line gonna get rid of the truck cause of the lack of power now it's not even a option.

5 years ago

Performance Modified Intake

We are proud to offer the only performance upgrade intake for 1988-1997 460’s. Whether you have built up your 460 or wanting more out of your stock motor letting it breath is always the answer to more horsepower and torque. Having seen the drastic performance increase with ported and balanced single plane manifolds paired with multi-port efi we had to give it a shot. The result was an instant and undeniably increase in powerStarting with Ford’s factory intake we start by cutting the stair-stepped bottom out. From there we remove all the internal passages. They are cut back into a balanced much short length. The air no longer has to get drawn through long runners that make sharp 90 degree turns. Instead each cylinder can now easily draw the air it needs to make the power a 460 is capable of. The easiest way to describe the difference is, instead of downshifting just lay into the throttle and watch the speedo climb. As always, we did 12 time trial pulls before and after the intakeThe difference was 1.75 seconds difference in 0-60 in the pictured blue and white 9000 lb. Monster. Everyone who has gone for a ride has said they all felt a huge difference. As the driver it feels like I just unhooked the flatbed trailer.

Depending on how quickly you need your new intake, there are two purchasing options:

Option 1: We don’t charge a core charge. You send us your intake for this service, and we verify that it’s usable. If it is, we send your new intake out the same day. Price includes S+H on delivery of your new intake.

Option 2: If you need your new intake faster, pre-pay the refundable core charge of $230. We will immediately ship your performance modified intake, simply send us your old one. Once we receive your intake in usable condition we refund the core charge fee.

Option 1: Without Core Charge

$470 (Includes S+H)

Option 2: With Core Charge

$700 (Includes S+H)

88-91 460 Harness Conversion Service

Re-mapped to a 96 layout includes converting/remapping: ignition module,  distributor, idle air control valve, & oxygen sensor.
This process on yours will include:
  • Completely stripping the harness and cycling it through our ultrasonic process (sounds cheesy but it makes the wires soft and flexible & like new again)
  • Testing and inspecting wires & connectors for continuity and damage
  • Remapping harness into: one, nice, clean, and functional layout
  • new updated Universal relays,
  • new fuses,
  • Removal of any questionable connections (covered in goo-tar),
  • Removal of dangerous failure prone factory:
diodes, resistors,  capacitors, and connections remapped to a 96 layout includes converting/remapping: ignition module,  distributor, idle air control valve, & oxygen sensor, new injector connectors if needed, any and all repairs needed, road testing your harness & ECU,
Additional outputs for:
  • After market tachometer, water temp, and after-market transmission controller (if needed)
  • Re-loomed and additional outputs labeled
  • I can also convert the pigtails for the throttle body, while it’s here (if you want to get it at the same time)
Also included will be:
  • New heated 4 wire Bosch oxygen sensor (15717),
  • Ignition module relocation block (Aluminum cooling mount for driver side one fender)
  • This will include shipping back to you.

$925 (Includes S+H)

PRE-ORDER: Howards Cams "460 EFI Guys Stage 1" Kit for EFI and Carb 460

.490 / .519 Lift, 112 LSA, 205 / 213 duration @ .050 lift, 4 degrees advance cut in for 108 intake centerline.  This is a clean and crisp torque cam that will not disappoint all the way up to the rev-limiter.

Expected Late-April, 2024
Includes:
  • Howard’s hydraulic flat tappet camshaft
  • Howard’s lifter set
  • True Roller Double-Roller Adjustable Timing Chain and Gear Set
  • new springs, locks and retainers
  • camshaft assembly lube

After years of trying hand fulls of camshafts we decided to modify our favorites and make our own lines.  We partnered up with Howard’s cams to get these custom made to our specifications.  Like so many others, we have fought low quality cams failing on us.  Not willing to take any chances ever again, we are thrilled to have partnered up with Howard’s Cams, and their unrivaled quality.  To be able to run this camshaft you have to swap to the included springs, locks, and retainers.  We have always had great spring pressure with this setup, however it is your responsibility to confirm proper spring pressure.  These parts are covered by a full replacement warranty from Howard’s Cams.  In the event of failure or problem other parts and or labor are not covered.

We just sold out of these!

We just ran out of these – we have 10 coming our way and are expecting them in Late-April.

An absolute must is to break  in your camshaft with Lucas Engine Break-In Oil 10636 you will want 2 gallons.

$790 (Includes S+H)

PRE-ORDER: Howards Cams "460 EFI Guys Stage 2" Kit for EFI and Carb 460

.519 / .519 Lift, 112 LSA, 219 / 225 duration @ .050 lift, 4 degrees advance cut in for 108 intake centerline.  This is an awesome all around EFI friendly cam.  It has a great exhaust tone, flat and strong torque curve, and will work flawlessly with Speed density EFI and make great power.

Expected Late-April, 2024
Includes:
  • Howard’s hydraulic flat tappet camshaft
  • Howard’s lifter set
  • True Roller Double-Roller Adjustable Timing Chain and Gear Set
  • new springs, locks and retainers (these are shaved retainers for this cam’s intake lift)
  • camshaft assembly lube

After years of trying hand fulls of camshafts we decided to modify our favorites and make our own lines.  We partnered up with Howard’s cams to get these custom made to our specifications.  Like so many others, we have fought low quality cams failing on us.  Not willing to take any chances ever again, we are thrilled to have partnered up with Howard’s Cams, and their unrivaled quality.  To be able to run this camshaft you have to swap to the included springs, locks, and retainers.  We have always had great spring pressure with this setup, however it is your responsibility to confirm proper spring pressure.  These parts are covered by a full replacement warranty from Howards Cams.  In the event of failure or problem other parts and or labor are not covered.

We just sold out of these!

Pre-order now:  we have 10 of these heading our way, and have been assured we will have them by late-April.  However, Howards has always exceeded delivery expectations for us.

An absolute must is to break  in your camshaft with Lucas Engine Break-In Oil 10636 you will want 2 gallons.

$810 (Includes S+H)

Howards Cams "460 EFI Guys Stage 3" Kit for EFI and Carb 460

.513 / .536 Lift, 112 LSA, 215 / 225 duration @ .050 lift, 4 degrees advance cut in for 108 intake centerline.  This is similar to the “Power beast cam”.  This cam sacrifices a little power down low to hit hard in the mid-to-high rpm range.

Includes:
  • Howard’s hydraulic flat tappet camshaft
  • Howard’s lifter set
  • True Roller Double-Roller Adjustable Timing Chain and Gear Set
  • new springs, locks and retainers
  • camshaft assembly lube

After years of trying hand fulls of camshafts we decided to modify our favorites and make our own lines.  We partnered up with Howard’s cams to get these custom made to our specifications.  Like so many others, we have fought low quality cams failing on us.  Not willing to take any chances ever again, we are thrilled to have partnered up with Howard’s Cams, and their unrivaled quality. To be able to run this camshaft you have to swap to the included springs, locks, and retainers.  We have always had great spring pressure with this setup, however it is your responsibility to confirm proper spring pressure.  These parts are covered by a full replacement warranty from Howard’s Cams.  In the event of failure or problem other parts and or labor are not covered.

An absolute must is to break  in your camshaft with Lucas Engine Break-In Oil 10636 you will want 2 gallons.

$790 (Includes S+H)

1988-1997 - FORD F-250/F-350 2WD/4WD 460 MOTOR MOUNT KITS

Ditch those squishy water bed style factory motor mounts. These Bullet-Proof motor mount kits will bolt directly in place of the factory mounts. Our goal was to make a quality mount that could handle high horsepower, keep your motor locked down and be smooth enough to use as a daily driver. These are built so well if there’s ever an issue, we replace them free of charge.

$200 (Includes S+H)

460 SWAP MOTOR MOUNT KITS TO REPLACE 351M/400 351W 302

If you are swapping from a 351M, 400, 351W or 302 to a 460 these will bolt directly to the perches that your truck, or bronco already have. They are for the year range 1974-1982. Additionally, they are built to the correct dimensions to allow you to use the full serpentine system and accessories of a stock EFI 460.

$195 (Includes S+H)

RV and VAN 460 MOTOR MOUNTS - 1982-1997

For the vans and RVs with a bolt spacing of 5 5/8″ these will replace the factory motor mounts, and you will re-use the cups that are bolted to the engine. Ditch those squishy water bed style factory motor mounts. These Bullet-Proof motor mount kits will bolt directly in place of the factory mounts. Our goal was to make a quality mount that could handle high horsepower, keep your motor locked down and be smooth enough to use as a daily driver. These are built so well if there’s ever an issue, we replace them free of charge.

$170 (includes S+H)

James
James
5/5

Excellent quality construction and a perfect fit on my 79 bronco.
Saved me a bunch of time and headache!

4 years ago

Ford 5.0 Intake Performance Package

These kits include the Edelbrock Victor Junior EFI Intake manifold and fuel rails. We also include our low profile throttle body. The factory intake is restrictive and draws air through great lengths of individual runners. By bolting on this setup your engine doesn’t have to breath through 8 long small straws. Allowing your engine to make much more power. You also will have a throttle response like never before. Almost everything you need to compete the swap comes in the kit

  • Edelbrock intake and fuel rails
  • Our Low-Profile Throttle Body (includes brand new idle air bypass and pigtail, and new TPS and pigtail)
  • An adjustable Fuel Pressure Regulator with gauge
  • New Conversion Throttle cable

You can increase the pressure and the volume of your fuel injectors with the included adjustable Fuel Pressure Regulator. You can also reuse your other factor sensors. All you will need is; Intake gaskets, some rubber fuel lines, and a flaring Tool. We recommend installing a wide band air fuel gauge, incase you need larger injectors.

$1500 (Includes S+H)

Ford 5.8 Intake Performance Package

These kits include the Edelbrock 351W Super Victor EFI intake and fuel rails. We also include our low profile throttle body. The factory intake is restrictive and draws air through great lengths of individual runners. By bolting on this setup your engine doesn’t have to breath through 8 long small straws. Allowing your engine to make much more power. You also will have a throttle response like never before. Almost everything you need to compete the swap comes in the kit

  • Edelbrock 351W Super Victor EFI intake and fuel rails
  • Our Low-Profile Throttle Body
  • Adjustable Remote Fuel Pressure Regulator
  • Throttle cable, sensors, and all needed hardware

If you have any of these parts call us and we can adjust the price accordingly. All you will need is; Intake gaskets, some rubber fuel lines, and a flaring Tool. Depending on if your engine is built up you may also need larger injectors.

$1720 (Includes S+H)