460 EFI : Engine Swaps

Swap in a 460 that is already fuel injected

You can swap in a complete factory EFI 460 engine from a 1988-1997. If you already have a 460 that is still good you can take the heads and intake from the 88-97 and put them on any 460 engine. A 460 will even bolt up to the same bellhousing that a 351M or 400 will.  Is it time to rebuild your 460 or Modified engine, or are you simply ready to ditch your carburetor and ignition system? Even if you’re just looking to add better fuel economy and power to your vehicle, an engine swap can be done in a day or two.

From there just send us the harness and ECU from the fuel injected truck, and we will convert it to our full stand-alone system.  If you are missing the harness or ECU we keep them in stock also.

If you want to make even more power install the new low-profile throttle body kit and also our performance upgrade Intake. Read more about them below.

Stand-alone conversion service

$650 (includes S+H)

Interested in Full Tuning Capabilities and/or Data Logging

With help from our friends at twEECer.com our stand-alone systems have gotten even better. With the additional purchase of a twEECer system they are now fully tunable. Changes are quick and easy with any aspect of ecu operation including: timing characteristics or advance, air/fuel curves, rev limits, even cold start operation. Write and store multiple tunes that can be switched even while running. This allows you to have your own performance tune, daily driver tune, mpg tune, valet mode, or even a kill switch shut down setting.

Purchase a new ECU from our stock

We keep 1996 ECUs in stock ready to go.  This year of ECU has the best air/fuel parameters and supports every engine from mild to wild flawlessly.  Each one is installed and tested before it ships out to you.

Purchase a harness from our stock

We keep a supply of wiring harnesses in stock. If you don’t get one when you found your EFI engine, we can use one of ours.

Low Profile Throttle Bodies for the 7.5 liter 460

By swapping to this throttle body, you will get better throttle response, increased horsepower, and increased torque. Your engine will come to life and perform like the beast it truly is. This throttle body improved our 0-60 times by 2 full seconds. We did 12 runs with the original throttle body and this one just to confirm it.

Included with this kit:

  • Throttle body adapters
  • Holley low profile throttle body, throttle cable and all needed sensors
  • Idle air bypass and grommet
  • Grommet and elbow for the driver side breather tube

Performance Modified Intake

We are proud to offer the only performance upgrade intake for 1988-1997 460’s. Whether you have built up your 460 or wanting more out of your stock motor letting it breath is always the answer to more horsepower and torque. Having seen the drastic performance increase with ported and balanced single plane manifolds paired with multi-port efi we had to give it a shot. The result was an instant and undeniably increase in powerStarting with Ford’s factory intake we start by cutting the stair-stepped bottom out. From there we remove all the internal passages. They are cut back into a balanced much short length. The air no longer has to get drawn through long runners that make sharp 90 degree turns. Instead each cylinder can now easily draw the air it needs to make the power a 460 is capable of. The easiest way to describe the difference is, instead of downshifting just lay into the throttle and watch the speedo climb. As always, we did 12 time trial pulls before and after the intakeThe difference was 1.75 seconds difference in 0-60 in the pictured blue and white 9000 lb. Monster. Everyone who has gone for a ride has said they all felt a huge difference. As the driver it feels like I just unhooked the flatbed trailer.

We don’t charge a core charge. Send us your intake for this service, and we verify that it’s usable. If it is we send your new intake out the same day. Price includes S+H on delivery of your new intake.


We have had countless customers utilize our 351M swap mounts as a universal motor mount. Why redesign the wheel if these work so well. We include (but do not weld) the perch bolt to give you more flexibility. Bolt them onto the engine then you can build your own frame perches from these out to the frame.

$160 (includes S+H)

Bullet-Proof Motor Mount Kits

After having every motor mount we have purchased fail we decided to make our own. These are a fully caged polyurethane motor mount kits. They hold the engine absolutely stable but won’t vibrate you to death. They will handle high horsepower engines but are daily driver friendly. Ours are built at zero degrees with a stock nose up engine. Many other companies are not. Each of our mount kits are made of DOM tubing, polyurethane bushings, plate steel and grade-8 hardware. A pro-rated warranty is laughable. Simply put if these ever fail or wear out we replace them free of charge.