Harland Sharp 7.5 Pedestal Mount Roller Rockers (1.8 Ratio)
1.8 Ratio Harland Sharp Pedestal Mount Adjustable Roller Rockers for 460, 429, 351C, 351M/400
Example of lift increase:
Stock cam of .473/.473 will now be .493/.493
Stage 1 cam of .490/.519 will now be .509/.540
***These will need our springs locks and retainers kits to offer you more room than stock set-up will provide***
460 EFI Guys has teamed up with Harland Sharp to offer our customers the highest quality roller rockers for their factory EFI and carbureted 460/429, 351C and 351M/400 heads. These are a full set of adjustable full roller rockers for factory pedestal mount Ford heads. No guide plates are required with these due to the design of the self-centering pedestal foot block.
Why upgrade you might ask? Don’t believe the nay-sayers. Roller rockers make a difference. Not all your valves are opening the same amount with stamped steel rockers. It gets worse with higher spring pressure and higher rpm. You will get more horsepower with roller rockers with less friction and less oil temperature and breakdown. If you’re looking for quality and performance these are the best option for consistency and accuracy in valve lift. It will help you to pull the maximum potential out of your camshaft.
Kit includes:
- 16 adjustable roller rockers, pedestal feet and bolts
- Set of shims to adjust contact point on the valve tip
Fits:
Pedestal mount factory Ford heads 7.5 / 460, 429, 351C, 351M/400 (1.8 ratio)
for spring pressures up to 600 lbs. at the nose of the cam.
Adjustable rocker set important notes*
- You will need to measure and order correct length pushrods. What we have found for the length on our builds is 8.350 in. (for flat tappet) & 7.850 in. (for Crower hydraulic roller lifters). Typically $100 for 5/16” or $150 for 3/8” pushrods.
- You will need to raise your 460 EFI stock valve covers ½”. We are now making these in house to correctly work with your factory valve covers, with no modifications.
$670 (Includes S+H)
Harness Conversion Service – Swapping from 4.9/5.0/5.8 to a EFI 460 Engine
If you are swapping from the 4.9/5.0/5.8 (with an EEC-IV/Speed Density) in a 1986-1997 to an EFI 460: you can send us your harness and we will convert it to the hybrid 1996 460 platform. This will allow you to keep all of your dash, instruments, and vehicle’s functionality working and intact. It will also allow you run a 460 speed density ECU – which is far superior to the smaller engines’ ECUs.
Howards Cams “460 EFI Guys Stage 1” Kit for EFI and Carb 460
.490 / .519 Lift, 112 LSA, 205 / 213 duration @ .050 lift, 4 degrees advance cut in for 108 intake centerline. This is a clean and crisp torque cam that will not disappoint all the way up to the rev-limiter.
- Howard’s hydraulic flat tappet camshaft
- Howard’s lifter set
- True Roller Double-Roller Adjustable Timing Chain and Gear Set
- Howards springs, locks and retainers
- Camshaft assembly lube
- Oil Pump priming rod
- 7 quarts of Lucas Engine SAE 30 break-in oil
- 16 ounces of Lucas ZDDP additive
- Valve Seals (Howard’s positive stop)
DON’T BUY JUNK CAMS NO MATTER THE NAME ON THE BOX. THEY DON’T KNOW WHAT WILL WORK WITH EFI OR THEY WILL WIPE OUT YOUR ENGINE, IT’S NOT WORTH SAVING A LITTLE MONEY.
These cams will work with your stock speed density 460 computer and deliver great results. Check out our youtube videos if you want to see them in action. Don’t shy away, they also work amazingly well in carbureted engines.
After years of trying and losing over 20 cams we decided to modify our favorites and make our own lines. We partnered up with Howard’s cams to get these custom made (IN THE USA) to our specifications. Like so many others, we have fought low quality cams failing on us (most of them with a big name on the package). Not willing to take any chances ever again, we are thrilled to have partnered up with Howard’s Cams, and their unrivaled quality. To be able to run this camshaft you have to swap to the included springs, locks, and retainers. We have always had great spring pressure with this setup, we rarely even put shims under these to hit our targeted 105 lbs. of seat pressure. We have never lost a single Howards camshaft, and to make sure you don’t either, we are sending you the same break-in oil we run. We also include a bottle of the zddp additive that the oil manufacturers stopped adding to protect your engine. The 16oz bottle we include is enough for 10 oil changes to come.
new cam kit price including oil and additive
Howards Cams “460 EFI Guys Stage 2” Kit for EFI and Carb 460
.519 / .519 Lift, 112 LSA, 219 / 225 duration @ .050 lift, 4 degrees advance cut in for 108 intake centerline.
This is an awesome all around EFI friendly cam. It has a great exhaust tone, flat and strong torque curve, and will work flawlessly with Speed density EFI and make great power. This cam will work with your stock speed density ecu and does not require a higher stall convertor. We have passed emissions tests with this cam flawlessly.
- Howard’s hydraulic flat tappet camshaft
- Howard’s lifter set
- True Roller Double-Roller Adjustable Timing Chain and Gear Set
- Howards springs, locks and retainers
- Camshaft assembly lube
- Oil Pump priming rod
- 7 quarts of Lucas Engine SAE 30 break-in oil
- 16 ounces of Lucas ZDDP additive
- Valve Seals (Howard’s positive stop)
DON’T BUY JUNK CAMS NO MATTER THE NAME ON THE BOX. THEY DON’T KNOW WHAT WILL WORK WITH EFI OR THEY WILL WIPE OUT YOUR ENGINE, IT’S NOT WORTH SAVING A LITTLE MONEY.
These cams will work with your stock speed density 460 computer and deliver great results. Check out our youtube videos if you want to see them in action. Don’t shy away, they also work amazingly well in carbureted engines.
After years of trying and losing over 20 cams we decided to modify our favorites and make our own lines. We partnered up with Howard’s cams to get these custom made (IN THE USA) to our specifications. Like so many others, we have fought low quality cams failing on us (most of them with a big name on the package). Not willing to take any chances ever again, we are thrilled to have partnered up with Howard’s Cams, and their unrivaled quality. To be able to run this camshaft you have to swap to the included springs, locks, and retainers. We have always had great spring pressure with this setup, we rarely even put shims under these to hit our targeted 105 lbs. of seat pressure. We have never lost a single Howards camshaft, and to make sure you don’t either, we are sending you the same break-in oil we run. We also include a bottle of the zddp additive that the oil manufacturers stopped adding to protect your engine. The 16oz bottle we include is enough for 10 oil changes to come.
new cam kit price including oil and additive
Howards Cams “460 EFI Guys Stage 3” Kit for EFI and Carb 460
.513 / .536 Lift, 112 LSA, 215 / 225 duration @ .050 lift, 4 degrees advance cut in for 108 intake centerline.
You can absolutely hear this cam. It is a tire frying animal. It is actually an improved upon design based off of the towing beast cam design. It has worked great with EFI. We have run even larger cams than this with the stock efi computers, but we learned to trim those back to this spec to be much happier for a daily driver, but still deliver great results. This one has an aggressive exhaust tone, flat and strong torque curve, and will work with Speed density EFI and make great power.
- Howard’s hydraulic flat tappet camshaft
- Howard’s lifter set
- True Roller Double-Roller Adjustable Timing Chain and Gear Set
- Howards springs, locks and retainers
- Camshaft assembly lube
- Oil Pump priming rod
- 7 quarts of Lucas Engine SAE 30 break-in oil
- 16 ounces of Lucas ZDDP additive
- Valve Seals (Howard’s positive stop)
DON’T BUY JUNK CAMS NO MATTER THE NAME ON THE BOX. THEY DON’T KNOW WHAT WILL WORK WITH EFI OR THEY WILL WIPE OUT YOUR ENGINE, IT’S NOT WORTH SAVING A LITTLE MONEY.
These cams will work with your stock speed density 460 computer and deliver great results. Check out our youtube videos if you want to see them in action. Don’t shy away, they also work amazingly well in carbureted engines.
After years of trying and losing over 20 cams we decided to modify our favorites and make our own lines. We partnered up with Howard’s cams to get these custom made (IN THE USA) to our specifications. Like so many others, we have fought low quality cams failing on us (most of them with a big name on the package). Not willing to take any chances ever again, we are thrilled to have partnered up with Howard’s Cams, and their unrivaled quality. To be able to run this camshaft you have to swap to the included springs, locks, and retainers. We have always had great spring pressure with this setup, we rarely even put shims under these to hit our targeted 105 lbs. of seat pressure. We have never lost a single Howards camshaft, and to make sure you don’t either, we are sending you the same break-in oil we run. We also include a bottle of the zddp additive that the oil manufacturers stopped adding to protect your engine. The 16oz bottle we include is enough for 10 oil changes to come.
new cam kit price including oil and additive
Lisle Valve Holders
You can use these in the truck or on an engine stand. Simply hook up your air compressor line and the air pressure will hold the valves from dropping while you install valve springs. These Lisle valve holders have 2-sizes for both 14mm and 18mm spark plug threads.
Low Profile Throttle Body – 7.5 Liter 460
** DOES NOT WORK WITH MAF (Mass Air Flow trucks) **
SPEED DENSITY HAVE 2 INTAKE TUBES CONNECTED TO THE AIR FILTER BOX
Included with this kit:
- Holley low profile throttle body, throttle cable and all needed sensors
- Throttle cable housing, inner-cable, and needed fittings for throttle and cruise control
- Idle air bypass, pigtail and tube
- Throttle position sensor and pigtail
- 5/8″ tubing and elbow for driver side breather port
- 14″ Air Filter Base (we drill and install a grommet for the IAC)
- 1″ air filter spacer (makes the install easier with more room over the fuel rails)
- MAP sensor and fuel pressure regulator vacuum tubing
- 3/8″ NPT plug for the intake runner #5 (when needed)
- ** Purchase a washable complete air Filter kit separately **
Pair of Brand New, Upgraded F3 460 EFI Cylinder Heads – Reworked with Bronze Manganese Valve Guides – for Flat Tappet or Roller Conversion Cam
Custom Built to Order. These are brand new castings, with improved wall thickness. We then rework them, and install bronze manganese valve guides. Diamond honed not reamed, micro-polished valves. Improved Valve job set up for lean burn EFI heat dissipation. Dressed with premium seals, springs, locks, and retainers. Shipping and handling included.
$2800 for Flat Tappet
$3000 for Roller
Performance Modified Intake
We are proud to offer the only performance upgrade intake for 1988-1997 460’s. Whether you have built up your 460 or wanting more out of your stock motor letting it breath is always the answer to more horsepower and torque. Having seen the drastic performance increase with ported and balanced single plane manifolds paired with multi-port efi we had to give it a shot. The result was an instant and undeniably increase in power. Starting with Ford’s factory intake we start by cutting the stair-stepped bottom out. From there we remove all the internal passages. They are cut back into a balanced much short length. The air no longer has to get drawn through long runners that make sharp 90 degree turns. Instead each cylinder can now easily draw the air it needs to make the power a 460 is capable of. The easiest way to describe the difference is, instead of downshifting just lay into the throttle and watch the speedo climb. As always, we did 12 time trial pulls before and after the intake. The difference was 1.75 seconds difference in 0-60 in the pictured blue and white 9000 lb. Monster. Everyone who has gone for a ride has said they all felt a huge difference. As the driver it feels like I just unhooked the flatbed trailer.
Depending on how quickly you need your new intake, there are two purchasing options:
Option 1: We don’t charge a core charge. You send us your intake for this service, and we verify that it’s usable. If it is, we send your new intake out the same day. Price includes S+H on delivery of your new intake.
Option 2: If you need your new intake faster, pre-pay the refundable core charge of $230. We will immediately ship your performance modified intake, simply send us your old one. Once we receive your intake in usable condition we refund the core charge fee.
